Add support for 28 pin msp430g2553 version and extra mhz options

hardware/msp430/boards.txt

@@ -28,6 +28,36 @@ lpmsp430g2452.build.core=msp430
 lpmsp430g2452.build.variant=launchpad
 lpmsp430g2452.upload.maximum_ram_size=256
 
+##############################################################
+lpmsp430g2553_1.name=LaunchPad w/ msp430g2553 (1MHz)
+lpmsp430g2553_1.upload.protocol=rf2500
+lpmsp430g2553_1.upload.maximum_size=16384
+lpmsp430g2553_1.build.mcu=msp430g2553
+lpmsp430g2553_1.build.f_cpu=1000000L
+lpmsp430g2553_1.build.core=msp430
+lpmsp430g2553_1.build.variant=launchpad
+lpmsp430g2553_1.upload.maximum_ram_size=512
+
+##############################################################
+lpmsp430g2553_8.name=LaunchPad w/ msp430g2553 (8MHz)
+lpmsp430g2553_8.upload.protocol=rf2500
+lpmsp430g2553_8.upload.maximum_size=16384
+lpmsp430g2553_8.build.mcu=msp430g2553
+lpmsp430g2553_8.build.f_cpu=8000000L
+lpmsp430g2553_8.build.core=msp430
+lpmsp430g2553_8.build.variant=launchpad
+lpmsp430g2553_8.upload.maximum_ram_size=512
+
+##############################################################
+lpmsp430g2553_12.name=LaunchPad w/ msp430g2553 (12MHz)
+lpmsp430g2553_12.upload.protocol=rf2500
+lpmsp430g2553_12.upload.maximum_size=16384
+lpmsp430g2553_12.build.mcu=msp430g2553
+lpmsp430g2553_12.build.f_cpu=12000000L
+lpmsp430g2553_12.build.core=msp430
+lpmsp430g2553_12.build.variant=launchpad
+lpmsp430g2553_12.upload.maximum_ram_size=512
+
 ##############################################################
 lpmsp430g2553.name=LaunchPad w/ msp430g2553 (16MHz)
 lpmsp430g2553.upload.protocol=rf2500
@@ -38,6 +68,36 @@ lpmsp430g2553.build.core=msp430
 lpmsp430g2553.build.variant=launchpad
 lpmsp430g2553.upload.maximum_ram_size=512
 
+##############################################################
+lpmsp430g2553_28pins_1.name=LaunchPad w/ msp430g2553 28pins (1MHz)
+lpmsp430g2553_28pins_1.upload.protocol=rf2500
+lpmsp430g2553_28pins_1.upload.maximum_size=16384
+lpmsp430g2553_28pins_1.build.mcu=msp430g2553
+lpmsp430g2553_28pins_1.build.f_cpu=1000000L
+lpmsp430g2553_28pins_1.build.core=msp430
+lpmsp430g2553_28pins_1.build.variant=launchpad_28pins
+lpmsp430g2553_28pins_1.upload.maximum_ram_size=512
+
+##############################################################
+lpmsp430g2553_28pins_8.name=LaunchPad w/ msp430g2553 28pins (8MHz)
+lpmsp430g2553_28pins_8.upload.protocol=rf2500
+lpmsp430g2553_28pins_8.upload.maximum_size=16384
+lpmsp430g2553_28pins_8.build.mcu=msp430g2553
+lpmsp430g2553_28pins_8.build.f_cpu=8000000L
+lpmsp430g2553_28pins_8.build.core=msp430
+lpmsp430g2553_28pins_8.build.variant=launchpad_28pins
+lpmsp430g2553_28pins_8.upload.maximum_ram_size=512
+
+##############################################################
+lpmsp430g2553_28pins_16.name=LaunchPad w/ msp430g2553 28pins (16MHz)
+lpmsp430g2553_28pins_16.upload.protocol=rf2500
+lpmsp430g2553_28pins_16.upload.maximum_size=16384
+lpmsp430g2553_28pins_16.build.mcu=msp430g2553
+lpmsp430g2553_28pins_16.build.f_cpu=16000000L
+lpmsp430g2553_28pins_16.build.core=msp430
+lpmsp430g2553_28pins_16.build.variant=launchpad_28pins
+lpmsp430g2553_28pins_16.upload.maximum_ram_size=512
+
 ##############################################################
 lpmsp430fr5739.name=FraunchPad w/ msp430fr5739
 lpmsp430fr5739.upload.protocol=rf2500

hardware/msp430/variants/launchpad_1/Board.mk

@@ -0,0 +1,9 @@
+######################################
+# Board specific
+ARCH = msp430
+MCU = msp430g2553
+MCU_FLAG = -mmcu=$(MCU)
+F_CPU = 1000000L
+FLASH_SIZE = 16384
+UPLOAD_COMMAND = $(MSPDEBUG) $(VERBOSE_UPLOAD) tilib --force-reset "prog build/$(SKETCH_NAME).bin"
+######################################

hardware/msp430/variants/launchpad_1/pins_energia.h

@@ -0,0 +1,306 @@
+/*
+  ************************************************************************
+  *   pins_energia.h
+  *
+  *   Energia core files for MSP430
+  *      Copyright (c) 2012 Robert Wessels. All right reserved.
+  *
+  *     Contribution: Rei VILO
+  *
+  ***********************************************************************
+  Derived from:
+  pins_arduino.h - Pin definition functions for Arduino
+  Part of Arduino - http://www.arduino.cc/
+
+  Copyright (c) 2007 David A. Mellis
+
+  This library is free software; you can redistribute it and/or
+  modify it under the terms of the GNU Lesser General Public
+  License as published by the Free Software Foundation; either
+  version 2.1 of the License, or (at your option) any later version.
+
+  This library is distributed in the hope that it will be useful,
+  but WITHOUT ANY WARRANTY; without even the implied warranty of
+  MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
+  Lesser General Public License for more details.
+
+  You should have received a copy of the GNU Lesser General
+  Public License along with this library; if not, write to the
+  Free Software Foundation, Inc., 59 Temple Place, Suite 330,
+  Boston, MA  02111-1307  USA
+*/
+
+#ifndef Pins_Energia_h
+#define Pins_Energia_h
+#ifndef BV
+#define BV(x) (1 << (x))
+#endif
+
+static const uint8_t SS      = 8;  /* P2.0 */
+static const uint8_t SCK     = 7;  /* P1.5 */
+static const uint8_t MOSI    = 15; /* P1.7 */
+static const uint8_t MISO    = 14; /* P1.6 */
+static const uint8_t TWISCL1  = 9;   /* P2.1 SW I2C */
+static const uint8_t TWISDA1  = 10;  /* P2.2 SW I2C */
+static const uint8_t TWISDA0  = 15;  /* P1.7 */
+static const uint8_t TWISCL0  = 14;  /* P1.6 */
+static const uint8_t DEBUG_UARTRXD = 3;  /* Receive  Data (RXD) at P1.1 */
+static const uint8_t DEBUG_UARTTXD = 4;  /* Transmit Data (TXD) at P1.2 */
+#define TWISDA1_SET_MODE  (INPUT)
+#define TWISCL1_SET_MODE  (INPUT)
+#if defined(__MSP430_HAS_USCI__)
+#define TWISDA0_SET_MODE  (PORT_SELECTION0 | PORT_SELECTION1 /* | INPUT_PULLUP*/) /* do not enable the pull ups for this device */
+#define TWISCL0_SET_MODE  (PORT_SELECTION0 | PORT_SELECTION1 /* | INPUT_PULLUP*/)
+#define DEBUG_UARTRXD_SET_MODE (PORT_SELECTION0 | PORT_SELECTION1 | INPUT)
+#define DEBUG_UARTTXD_SET_MODE (PORT_SELECTION0 | PORT_SELECTION1 | OUTPUT)
+#define SPISCK_SET_MODE (PORT_SELECTION0 | PORT_SELECTION1)
+#define SPIMOSI_SET_MODE (PORT_SELECTION0 | PORT_SELECTION1)
+#define SPIMISO_SET_MODE (PORT_SELECTION0 | PORT_SELECTION1)
+#endif
+#if defined(__MSP430_HAS_USI__)
+#define TWISDA0_SET_MODE  (PORT_SELECTION0 | INPUT_PULLUP)
+#define TWISCL0_SET_MODE  (PORT_SELECTION0 | INPUT_PULLUP)
+#define DEBUG_UARTRXD_SET_MODE (PORT_SELECTION0 | INPUT)
+#define DEBUG_UARTTXD_SET_MODE (PORT_SELECTION0 | OUTPUT)
+#define SPISCK_SET_MODE (PORT_SELECTION0)
+#define SPIMOSI_SET_MODE (PORT_SELECTION0)
+#define SPIMISO_SET_MODE (PORT_SELECTION0)
+#endif
+
+/* Define the default I2C settings */
+#define DEFAULT_I2C -1 /* indicates SW I2C on pseudo module 1 */
+#define TWISDA TWISDA1
+#define TWISCL TWISCL1
+#define TWISDA_SET_MODE  TWISDA1_SET_MODE
+#define TWISCL_SET_MODE  TWISCL1_SET_MODE
+
+#define DEBUG_UART_MODULE_OFFSET 0x0
+
+#define DEBUG_UART_MODULE 0x0
+
+static const uint8_t A0  = 2;
+static const uint8_t A1  = 3;
+static const uint8_t A2  = 4;
+static const uint8_t A3  = 5;
+static const uint8_t A4  = 6;
+static const uint8_t A5  = 7;
+static const uint8_t A6  = 14;
+static const uint8_t A7  = 15;
+static const uint8_t A10 = 128 + 10; // special. This is the internal temp sensor
+
+//                      +-\/-+
+//               VCC   1|    |20  GND
+//         (A0)  P1.0  2|    |19  XIN
+//         (A1)  P1.1  3|    |18  XOUT
+//         (A2)  P1.2  4|    |17  TEST
+//         (A3)  P1.3  5|    |16  RST#
+//         (A4)  P1.4  6|    |15  P1.7  (A7) (SCL) (MISO) depends on chip
+//         (A5)  P1.5  7|    |14  P1.6  (A6) (SDA) (MOSI)
+//               P2.0  8|    |13  P2.5
+//               P2.1  9|    |12  P2.4
+//               P2.2 10|    |11  P2.3
+//                      +----+
+//
+
+// Pin names based on the silkscreen
+//
+static const uint8_t P1_0 = 2;
+static const uint8_t P1_1 = 3;
+static const uint8_t P1_2 = 4;
+static const uint8_t P1_3 = 5;
+static const uint8_t P1_4 = 6;
+static const uint8_t P1_5 = 7;
+static const uint8_t P2_0 = 8;
+static const uint8_t P2_1 = 9;
+static const uint8_t P2_2 = 10;
+static const uint8_t P2_3 = 11;
+static const uint8_t P2_4 = 12;
+static const uint8_t P2_5 = 13;
+static const uint8_t P1_6 = 14;
+static const uint8_t P1_7 = 15;
+static const uint8_t P2_7 = 18;
+static const uint8_t P2_6 = 19;
+
+static const uint8_t RED_LED = 2;
+static const uint8_t GREEN_LED = 14;
+static const uint8_t PUSH2 = 5;
+static const uint8_t TEMPSENSOR = 128 + 10; // depends on chip
+
+
+#ifdef ARDUINO_MAIN
+
+const uint16_t port_to_input[] = {
+   NOT_A_PORT,
+   (uint16_t) &P1IN,
+   (uint16_t) &P2IN,
+#ifdef __MSP430_HAS_PORT3_R__
+   (uint16_t) &P3IN,
+#endif
+};
+
+const uint16_t port_to_output[] = {
+   NOT_A_PORT,
+   (uint16_t) &P1OUT,
+   (uint16_t) &P2OUT,
+#ifdef __MSP430_HAS_PORT3_R__
+   (uint16_t) &P3OUT,
+#endif
+};
+
+const uint16_t port_to_dir[] = {
+   NOT_A_PORT,
+   (uint16_t) &P1DIR,
+   (uint16_t) &P2DIR,
+#ifdef __MSP430_HAS_PORT3_R__
+   (uint16_t) &P3DIR,
+#endif
+};
+
+const uint16_t port_to_ren[] = {
+   NOT_A_PORT,
+   (uint16_t) &P1REN,
+   (uint16_t) &P2REN,
+#ifdef __MSP430_HAS_PORT3_R__
+   (uint16_t) &P3REN,
+#endif
+};
+
+const uint16_t port_to_sel0[] = {  /* put this PxSEL register under the group of PxSEL0 */
+   NOT_A_PORT,
+   (uint16_t) &P1SEL,
+   (uint16_t) &P2SEL,
+#ifdef __MSP430_HAS_PORT3_R__
+   (uint16_t) &P3SEL,
+#endif
+};
+
+const uint16_t port_to_sel2[] = {
+   NOT_A_PORT,
+#ifdef P1SEL2_
+   (uint16_t) &P1SEL2,
+#else
+        NOT_A_PORT,
+#endif
+#ifdef P2SEL2_
+   (uint16_t) &P2SEL2,
+#else 
+        NOT_A_PORT,
+#endif
+#ifdef P3SEL2_
+   (uint16_t) &P3SEL2,
+#else
+        NOT_A_PORT,
+#endif
+};
+
+
+/* 
+ * Defines for devices with 2x TA3 timers (e.g. MSP430g2553). On the 20pin devices, upto 3 analog outputs are available
+ * T0A1, T1A1 and T1A2 
+ */
+const uint8_t digital_pin_to_timer[] = {
+   NOT_ON_TIMER, /*  dummy */
+   NOT_ON_TIMER, /*  1 - VCC */
+   NOT_ON_TIMER, /*  2 - P1.0 */
+   T0A0,         /*  3 - P1.1, note: A0 output cannot be used with analogWrite */
+   T0A1,         /*  4 - P1.2 */
+   NOT_ON_TIMER, /*  5 - P1.3 */
+   NOT_ON_TIMER, /*  6 - P1.4 note: special case. Leaving as no timer due to difficulty determining if available */
+   T0A0,         /*  7 - P1.5 note: A0 output cannot be used with analogWrite  */
+#if defined(__MSP430_HAS_T1A3__) 
+   T1A0,         /*  8 - P2.0 note: A0 output cannot be used with analogWrite */
+   T1A1,         /*  9 - P2.1 */
+   T1A1,         /* 10 - P2.2 */
+   T1A0,         /* 11 - P2.3 note: A0 output cannot be used with analogWrite  */
+   T1A2,         /* 12 - P2.4 */
+   T1A2,         /* 13 - P2.5 */
+#else
+   NOT_ON_TIMER, /*  8 - P2.0 */
+   NOT_ON_TIMER, /*  9 - P2.1 */
+   NOT_ON_TIMER, /* 10 - P2.3 */
+   NOT_ON_TIMER, /* 11 - P2.4 */
+   NOT_ON_TIMER, /* 12 - P2.5 */
+   NOT_ON_TIMER, /* 13 - P2.6 */
+#endif
+   T0A1,         /* 14 - P1.6 */
+   NOT_ON_TIMER, /* 15 - P1.7 */
+   NOT_ON_TIMER, /* 16 - /RESET */  
+   NOT_ON_TIMER, /* 17 - TEST */  
+   NOT_ON_TIMER, /* 18 - XOUT - P2.7 */
+   T0A1,         /* 19 - XIN - P2.6: */
+   NOT_ON_TIMER, /* 20 - GND */
+};
+
+const uint8_t digital_pin_to_port[] = {
+   NOT_A_PIN, /* dummy */
+   NOT_A_PIN, /* 1 */
+   P1, /* 2 */
+   P1, /* 3 */
+   P1, /* 4 */
+   P1, /* 5 */
+   P1, /* 6 */
+   P1, /* 7 */
+   P2, /* 8 */
+   P2, /* 9 */
+   P2, /* 10 */
+   P2, /* 11 */
+   P2, /* 12 */
+   P2, /* 13 */
+   P1, /* 14 */
+   P1, /* 15 */
+   NOT_A_PIN, /* 16 */
+   NOT_A_PIN, /* 17 */
+   P2, /* 18 */
+   P2, /* 19 */
+   NOT_A_PIN, /* 20 */
+};
+
+const uint8_t digital_pin_to_bit_mask[] = {
+   NOT_A_PIN, /* 0,  pin count starts at 1 */
+   NOT_A_PIN, /* 1,  VCC */
+   BV(0),     /* 2,  port P1.0 */
+   BV(1),     /* 3,  port P1.1 */
+   BV(2),     /* 4,  port P1.2 */
+   BV(3),     /* 5,  port P1.3*/
+   BV(4),     /* 6,  port P1.4 */
+   BV(5),     /* 7,  port P1.5 */
+   BV(0),     /* 8,  port P2.0 */
+   BV(1),     /* 9,  port P2.1 */
+   BV(2),     /* 10, port P2.2 */
+   BV(3),     /* 11, port P2.3 */
+   BV(4),     /* 12, port P2.4 */
+   BV(5),     /* 13, port P2.5 */
+   BV(6),     /* 14, port P1.6 */
+   BV(7),     /* 15, port P1.7 */
+   NOT_A_PIN, /* 16, RST */
+   NOT_A_PIN, /* 17, TEST */
+   BV(7),     /* 18, XOUT */
+   BV(6),     /* 19, XIN */
+   NOT_A_PIN, /* 20, GND */
+};
+const uint32_t digital_pin_to_analog_in[] = {
+        NOT_ON_ADC,     /*  dummy   */
+        NOT_ON_ADC,     /*  1 - 3.3V*/
+        0,            /*  2 - A0 */
+        1,              /*  3 - A1 */
+        2,             /*  4 - A2 */
+        3,             /*  5 - A3 */
+        4,             /*  6 - A4 */
+        5,            /*  7 - A5 */
+        NOT_ON_ADC,    /*  8 - P2.0 */
+        NOT_ON_ADC,    /*  9 - P2.1 */
+        NOT_ON_ADC,    /*  10 - P2.2 */
+        NOT_ON_ADC,    /*  11 - P2.3 */
+        NOT_ON_ADC,    /*  12 - P2.4 */
+        NOT_ON_ADC,    /*  13 - P2.5 */
+        6,              /*  14 - A6 */
+        7,              /*  15 - A7 */
+        NOT_ON_ADC,    /*  16 - RST */
+        NOT_ON_ADC,     /*  17 - PF0 */
+        NOT_ON_ADC,    /*  18 - PE0 */
+        NOT_ON_ADC,     /*  19 - PB2 */
+        NOT_ON_ADC     /*  20 - GND */
+};
+
+#endif
+#endif